the connor-winfield corp . 2111 comprehensive drive. aurora, il 60505.fax (630) 851-5040. phone (630) 851-4722. www.conwin.com product da ta sheet specifications subject to change without notice. data sheet #: rev: date: page of copyright 2001 connor-winfield all rights reserved. a cr yst al controlled oscilla tors the connor winfield vsh5x- xxxg series are 5.0v surface mount hcmos, voltage control crystal oscillator (vcxo). based on a fundamental crystal design the vsh5x-xxxg series are designed for phased lock loop applications requiring low jitter and tight frequency stability. 1 2 vsh51022g - 27 mhz vcxo series center frequency features description ordering information 5.0v operation frequency range: 125 khz to 33 mhz temperature range: 0 to 70cfrequency stability : vsh51-xxxg: 25ppm low jitter <1 ps surface mount p ackage tape and reel packaging rohs compliant / lead free vsh52-xxxg: 50ppm vsh53-xxxg: 100ppm vsh54-xxxg: 20ppm s u r f a c e m o u n t 5 . 0 v h c m o s v c x o vsh51-xxxg- series vsh52-xxxg- seriesvsh53-xxxg- series vsh54-xxxg- series vx560 00 06/30/06 cw 06 26 vs h510 22g 27. 0m absolu te max imum rating s table 1.0 parameter units minimum nominal maxi mum units note storage temperature - 40 - 85 c supply voltage (vcc) - 0.5 - 7 vdc control voltage (vc) - 0.5 - 7 vdc model specifications model number table 2. 0 vsh51 - xxxg frequency stability: - 25 - 25 ppm 1 vsh52 - xxxg frequency stability: - 50 - 50 ppm 1 vsh53 - xxxg frequency stability: - 100 - 100 ppm 1 vsh54 - xxxg frequency stability: - 2 0 - 20 ppm 1 control voltage codes (x - add code to model number) table 3.0 0 control voltage vc 0.5 - 4.5 vdc 2 1 control voltage vc 0.0 - 5.0 vdc 2 dev iation codes (xx - add code to model number) table 4.0 12 frequency deviation: 100 - - ppm 3 15 frequency deviation: 150 - - ppm 3 16 frequency devi ation: 160 - - ppm 3 22 frequency deviation: 200 - - ppm 3 32 frequency deviation: 300 - - ppm 3 operating specific ations table 4.0 parameter minimum nominal maxi mum units no te frequency range (fo) 0.125 - 33 mhz operating temperature range 0 - 70 c supply voltage (vcc) 4.75 5.0 5.25 vdc supply current (icc) - - 30 ma jitter (bw=10hz to 20mhz) - - 5 ps rms jitter (bw=12khz to 20mhz) - - 1 ps rms ssb phase noise at 100hz offset - - 90 - dbc/hz ssb phase noise at 1khz offset - - 100 - dbc/hz ssb phase noise at 10khz offset - - 125 - dbc/hz ssb phase noise at 100khz offset - - 135 - dbc/hz input characteristics table 5.0 paramet er minimum nominal maxi mum units note monotonic linearity - 15 - 15 % input impedance - 50k - ohm modulation bandwidth (3db) 15 - - khz hcmos output characteristics table 6.0 parameter minimum nominal maxi mum units note load - - 15 pf voltage (voh) 4.5 - - vdc (vol) - - 0.5 vdc current (ioh) - 4 - - ma (ioh) - - 4 ma rise / fall time 10% to 90% - - 6 ns duty cycle measured at 2.5 vdc (standard) 45 50 55 % duty cycle measured at 1.4 vdc (op tional add t to model number) 45 50 55 % packag e characteristics table 7.0 package hermetically sealed, leadless ceramic surface mount package.
the connor-winfield corp . 2111 comprehensive drive. aurora, il 60505.fax (630) 851-5040. phone (630) 851-4722. www.conwin.com product da ta sheet specifications subject to change without notice. data sheet #: rev: date: page of copyright 2001 connor-winfield all rights reserved. a cr yst al controlled oscilla tors rev: date: page of 2 2 vx560 00 06/30/06 c o n tr o l v o lt a g e 1 5 p f 2 4 7 9 1 2 0 c 1 5 0 c 1 8 0 c 2 6 0 c 0 2 2 0 c 3 6 0 s e c . m a x . 1 2 0 s m a x . 1 0 s 6 0 s m a x . t im e t e m p e ra tu re 2 6 0 c pin connections solder profile package outline and dimensions output waveform t est circuit note: 1) frequency stability vs change in tem perature, referenced to frequenc y measured at 25 c with contro l voltage @ 2.50vdc. 2) positive transfer slope. 3) referenced to fo @ 25 c v s h 5 1 2 2 02 7. 0m - s u rf a c e m o u n t v c x o s e ri e s 0 c o n tr o l v o lt a g e 0 .5 t o 4 .5 v d c m in im u m d e v ia ti o n o f + /- 1 0 0 p p m o v e r th e c o n tr o l v o lt a g e r a n g e o p ti o n a l d u ty c y c le c o d e g r o h s c o m p lia n t / l e a d f re e c e n te r f re q u e n c y e x a m p le m o d e l n u m b e r table 8.0 pad connection 1 n/c 2 control voltage 3 n/c 4 ground 5 n/c 6 n/c 7 output 8 n/c 9 vcc 10 n/c suggested pad layout c w 0 6 2 6 v s h 5 1 0 2 2 g 2 7 . 0 m
|
